Depot Locator
-
one -
two
Introduction Section
Lorem ipsum dolor sit amet.
Ranges Section
Our skilled national hoist team is ready to support you in planning, configuring and supplying hoists to meet all your lifting needs, both above and below ground.
We are proud to offer you the largest construction hoist fleet of personnel and materials hoists in Europe, so whether you need support in a solution to build the next Shard or are assessing project plans to go safely underground we're here to help.
pr 5
<p>pr 5</p>
pr 2
<p>iven by one, two or three geared brake motors, depending on the payload of the cage. The geared motor drives a pinion acting on the mast rack to move the hoist cage in the desired direction. In addition to the drive motors there is a completely independent ‘safety device’ that comes in to play should the hoist cage exceed its rated travel speed in a downward direction. This brings the</p>
Test home page
pr 3
We are changing
pr 1
<p>iven by one, two or three geared brake motors, depending on the payload of the cage. The geared motor drives a pinion acting on the mast rack to move the hoist cage in the desired direction. In addition to the drive motors there is a completely independent ‘safety device’ that comes in to play should the hoist cage exceed its rated travel speed in a downward direction. This brings the</p>
exp sol for new cat
apr 4
<p>pr 4</p>
Services Section
The operation of goods only hoists is carried out from the ground level using a pendant control attached to the base electrical enclosure by a cable. This allows the operator to stand back from the hoist, enabling him to see the required landing level and stop the hoist cage within the permitted zone. If the hoist cage stops outside the pe
serv 4
<p>The operation of goods only hoists is carried out from the ground level using a pendant control attached to the base electrical enclosure by a cable. This allows the operator to stand back from the hoist, enabling him to see the required landing level and stop the hoist cage within the permitted zone. If the hoist cage stops outside the pe</p>
Solutions testserv 1
<p>The operation of goods only hoists is carried out from the ground level using a pendant control attached to the base electrical enclosure by a cable. This allows the operator to stand back from the hoist, enabling him to see the required landing level and stop the hoist cage within the permitted zone. If the hoist cage stops outside the pe</p>
serv 3
<p>The operation of goods only hoists is carried out from the ground level using a pendant control attached to the base electrical enclosure by a cable. This allows the operator to stand back from the hoist, enabling him to see the required landing level and stop the hoist cage within the permitted zone. If the hoist cage stops outside the pe</p>
Test home page
serv 2
Cross/Up-Sell Section
While most hoist applications can be fulfilled by configuration of standard hoist components, our fully equipped workshops can modify hoist cages and accessories for those awkward requirements.
cross 2
While most hoist applications can be fulfilled by configuration of standard hoist components, our fully equipped workshops can modify hoist cages and accessories for those awkward requirements.
cross 1
While most hoist applications can be fulfilled by configuration of standard hoist components, our fully equipped workshops can modify hoist cages and accessories for those awkward requirements.
cross 3
FAQs Section
Winch units are available with a variety of chain lengths and 1000 or 2000Kg lifting capacity.
All Sunbelt Rentals winches operate at 415 volts, 3 phase - to give added reliability - and are controlled from an attached pendant.
-
Answer Text 1
-
ACCESSORIES
To enable our standard hoist cages and industrial lifts to be configured for maximum safety and efficiency, Sunbelt Rentals offers a range of accessories that are available for most hoists. These include:
Landing Protection Panels – The panels are fitted either side of the landing gate to prevent site staff from touching the hoist cage as it travels past – or stops at – the landing. These are secured to the hoist vertical pipe superstructure and are fitted during the hoist installation.
Landing Infill Plates – Infill plates are installed to bridge the gap between the hoist superstructure and the site landings. The use of landing infill plates also restricts the gap between the hoist cage floor edge and landing edge to below 50mm as required by BS7212.
Foundation Steel Plates – Designed to avoid the necessity to fix the hoist base assembly down to concrete floors, or where the hoist is placed on a soft surface. GB Access can supply a steel plate to go under the hoist base which is bolted down to the plate. The standard F S P plate size is 4000 x 2500 x 40mm and weighs 3200Kg, which is sufficient to absorb the upwards forces in the event of a hoist striking the bottom buffers.
Landing Bridges – Where the hoist is mounted away from the building or scaffolding landing edge, we can supply and install a landing bridge. This will provide a safe walkway between the hoist cage and landing. The landing bridges are equipped with protection panels at the hoist end and full length handrails and toeboards to minimise the risk of items falling from the bridge.
Landing bridges are the same width as the hoist cage and available in lengths up to 6.0 metres.
Top Hats – These are available to be fitted to the roof of passenger goods hoists over the cage roof trapdoor. This allows the safe transportation of long items within the cage / top hat, without the possibility of the load falling from the hoist cage.
Pipe Carriers – These can be fitted to goods only hoists and enable scaffold poles etc. to be carried -
Winch units are available with a variety of chain lengths and 1000 or 2000Kg lifting capacity.